Faculty of New Sciences and Technologies, University of TehranIranian journal of Ecohydrology2423-60981320141222Initial PagesInitial Pages135458410.22059/ije.2014.54584FAJournal Article20150822https://ije.ut.ac.ir/article_54584_da73f3b21001b7fe05db1f3ca2e602e3.pdfFaculty of New Sciences and Technologies, University of TehranIranian journal of Ecohydrology2423-60981320141222Assessing groundwater quality and selection of the most appropriate spatial interpolation method (Case study: West of Marivan city, Iran)Assessing groundwater quality and selection of the most appropriate spatial interpolation method (Case study: West of Marivan city, Iran)1531665421810.22059/ije.2014.54218FAHosseinSalehiMSc Student, Department of Range and Watershed Management Engineering, Lorestan University, Lorestan, IranHosseinZeinivandDepartment of Range and Watershed Management Engineering, Lorestan University, Lorestan, Iran.Journal Article20141204Groundwater quality assessment and selection of appropriate methods of zoning depends on the region conditions, and data availability. The correct choice is a key milestone and a major step forward in the management of groundwater resources. The aim of this study was to evaluate the quality of groundwater for drinking and irrigation purposes in the west of Marivan city, Iran. For this purpose, data from 1985 to 2011, and the parameters of salinity, chlorine, concentration of dissolved substances, sulfate, water hardness, sodium, sodium adsorption ratio were used. Analysis of variance (ANOVA) and the LDS test was used to compare treatments and the differences between various stations respectively. For determining the most appropriate location and zoning methods for the above parameters, geographical information system was used. For this purpose, a geostatistics method of simple Kriging, and deterministic techniques such as inverse distance weighting, radial basis function, local estimator and general estimates was applied to annual and season data. The results showed that the quality of water in the area is appropriate and acceptable for drinking. Also for the irrigation, most of the study area is located within an acceptable range. Spatial interpolation results according to the root mean squared error (RMSE) and mean absolute error (MAE), among the different methods of interpolation techniques the LP for estimating the parameters of sulfate, soluble solids concentration and salinity, the RBF for for estimating parameters of sodium and sodium absorption ratio, the GPI method for chlorine at annual scale were the most appropriate methodsGroundwater quality assessment and selection of appropriate methods of zoning depends on the region conditions, and data availability. The correct choice is a key milestone and a major step forward in the management of groundwater resources. The aim of this study was to evaluate the quality of groundwater for drinking and irrigation purposes in the west of Marivan city, Iran. For this purpose, data from 1985 to 2011, and the parameters of salinity, chlorine, concentration of dissolved substances, sulfate, water hardness, sodium, sodium adsorption ratio were used. Analysis of variance (ANOVA) and the LDS test was used to compare treatments and the differences between various stations respectively. For determining the most appropriate location and zoning methods for the above parameters, geographical information system was used. For this purpose, a geostatistics method of simple Kriging, and deterministic techniques such as inverse distance weighting, radial basis function, local estimator and general estimates was applied to annual and season data. The results showed that the quality of water in the area is appropriate and acceptable for drinking. Also for the irrigation, most of the study area is located within an acceptable range. Spatial interpolation results according to the root mean squared error (RMSE) and mean absolute error (MAE), among the different methods of interpolation techniques the LP for estimating the parameters of sulfate, soluble solids concentration and salinity, the RBF for for estimating parameters of sodium and sodium absorption ratio, the GPI method for chlorine at annual scale were the most appropriate methodshttps://ije.ut.ac.ir/article_54218_15f9de4172cf5b649997576bfc1e2c88.pdfFaculty of New Sciences and Technologies, University of TehranIranian journal of Ecohydrology2423-60981320141222Predicting streamflow using data-driven model and time seriesPredicting streamflow using data-driven model and time series1671795421910.22059/ije.2014.54219FASeyed MortezaSeyedianFaculty of agriculture, University of Gonbad-Kavous, Gonbad-Kavous, IranMaryamSoleimaniMaster student in watershed management, Amol UniversityMojtabaKashaniFaculty of sciences, University of Gonbad-Kavous, Gonbad-Kavous, IranJournal Article20141116Accurate forecasting of streamflows has been one of the most important issues as it plays a key role in allotment of water resources. River flow simulations to determine the future river flows are important and practical. Given the importance of flow in the coming years, in this research three stations: Haji Qooshan, Ghare Shoor and Tamar in Gorganrood cachment were simulated in 2002-2011. To simulate river flow, time series (Auto Regression) and data driven based on support vector machine (SVM) was used for both monthly and weekly. The results showed that both methods in Tamar have low precision and Haji Qooshan station have good precision in monthly simulation. SVM increase 0.29 coefficient determination and decreases 0.35 RMSE error in Ghare Shoor station and perform more accurate than time series. Both methods simulate weekly discharge in low precision in Tamar and Ghare Shoor. Coefficient determination of time series is 0.91 and SVM is 0.86 in weekly simulation. DDR statistics show that the SVM has greater precision than time series in monthly simulation and equal precision in weekly simulation in Haji Qooshan station. The results of this study show that the SVM method is more accurate than time series in monthly and weekly simulation. The accuracy of both methods is on monthly basis rather than weekly. The accuracy of both methods is greater on monthly rather than weekly.Accurate forecasting of streamflows has been one of the most important issues as it plays a key role in allotment of water resources. River flow simulations to determine the future river flows are important and practical. Given the importance of flow in the coming years, in this research three stations: Haji Qooshan, Ghare Shoor and Tamar in Gorganrood cachment were simulated in 2002-2011. To simulate river flow, time series (Auto Regression) and data driven based on support vector machine (SVM) was used for both monthly and weekly. The results showed that both methods in Tamar have low precision and Haji Qooshan station have good precision in monthly simulation. SVM increase 0.29 coefficient determination and decreases 0.35 RMSE error in Ghare Shoor station and perform more accurate than time series. Both methods simulate weekly discharge in low precision in Tamar and Ghare Shoor. Coefficient determination of time series is 0.91 and SVM is 0.86 in weekly simulation. DDR statistics show that the SVM has greater precision than time series in monthly simulation and equal precision in weekly simulation in Haji Qooshan station. The results of this study show that the SVM method is more accurate than time series in monthly and weekly simulation. The accuracy of both methods is on monthly basis rather than weekly. The accuracy of both methods is greater on monthly rather than weekly.https://ije.ut.ac.ir/article_54219_3f477a386499dda25326dc49236d2386.pdfFaculty of New Sciences and Technologies, University of TehranIranian journal of Ecohydrology2423-60981320141222The Management Strategies to Reduce the Vulnerability of Flood in Tehran
(Case Study: District 1 and 3)The Management Strategies to Reduce the Vulnerability of Flood in Tehran
(Case Study: District 1 and 3)1811935422110.22059/ije.2014.54221FAHosseinYousefiFaculty of New Sciences and Technologies, University of TehranYounesNoorollahiFaculty of New Sciences and Technologies, University of Tehranhttps://orcid.org/00KeyvanSoltaniMaster student in Nature Engineering, Faculty of New Sciences and Technologies, University of TehranZahraJavadzadehMaster student in Nature Engineering, Faculty of New Sciences and Technologies, University of TehranJournal Article20141205The aim of this study is to assess effective factors in flooding and determine vulnerable areas in first and third Tehran Municipality areas, therefore suggest the proper management ways to avoid this disaster. Flooding disaster could have serious financial and fatal casualties, specially in urban areas. To reduce damages and hurts of flooding in these areas, hydrological, topographical, human features and … were used as separated layers in GIS and they were prioritized with a method like AHP. As the results areas with risks of flooding were determined. In this study the areas with high risks and low risks were recognized. Studying area was classified into five different classes and their areas were calculated. The very high risk area occurs in 16.21 square kilometer and respectively 19.11, 17.06, 9.67 and 1.84 square kilometer of areas were classified as high, medium, low and very low risks areas. By using this information, there could be proper plans and strategies to control floods and even utilizing flood water.The aim of this study is to assess effective factors in flooding and determine vulnerable areas in first and third Tehran Municipality areas, therefore suggest the proper management ways to avoid this disaster. Flooding disaster could have serious financial and fatal casualties, specially in urban areas. To reduce damages and hurts of flooding in these areas, hydrological, topographical, human features and … were used as separated layers in GIS and they were prioritized with a method like AHP. As the results areas with risks of flooding were determined. In this study the areas with high risks and low risks were recognized. Studying area was classified into five different classes and their areas were calculated. The very high risk area occurs in 16.21 square kilometer and respectively 19.11, 17.06, 9.67 and 1.84 square kilometer of areas were classified as high, medium, low and very low risks areas. By using this information, there could be proper plans and strategies to control floods and even utilizing flood water.https://ije.ut.ac.ir/article_54221_e6a861d391812b61308dc9dba5552e7b.pdfFaculty of New Sciences and Technologies, University of TehranIranian journal of Ecohydrology2423-60981320141222Validation of Global Climate Models (GCMS) Temperature and Rainfall Simulation in Kermanshah, Ravansar and West Islamabad StationsValidation of Global Climate Models (GCMS) Temperature and Rainfall Simulation in Kermanshah, Ravansar and West Islamabad Stations1952065422310.22059/ije.2014.54223FAMansoorHosseinikhahMSc Student in Watershed Management and Engineering, Department of Range and Watershed Management Engineering, Lorestan University, Lorestan, IranHosseinZeinivandDepartment of Range and Watershed Management Engineering, Lorestan University, Lorestan, IranAliHaghizadehDepartment of Range and Watershed Management Engineering, Lorestan University, Lorestan, IranNaserTahmasebipourDepartment of Range and Watershed Management Engineering, Lorestan University, Lorestan, IranJournal Article20150106The objective of this study was to evaluate the ability of ten GCMs and three Emission Scenarios to reproduce the rainfall and temperature parameters in Kermanshah, Ravansar and West Islamabad stations located inside Qaresou basin in Iran using the average weighting method, over 1989-2008 period. At first, the models output and the scenarios were provided for this period. Then, the models validation was carried out using Mean Absolute Error (MAE), Root Mean Square Error (RMSE), Model Bias, and Nash – Sutcliffe criteria. Moreover, the models and scenarios uncertainty analysis was assessed by the weighting method. Based on these criteria, HADGEM1 and BCM2 had the best efficiency in Kermanshah station for mean temperature and rainfall simulation respectively. For Ravansar station the best models were ECHO-G and HADCM3, while for West Islamabad was ECHO-G. The overall results of this analysis showed that the best applied GCMs and emission scenarios for simulation of temperature and rainfall in the study area are ECHO-G (A2) and HADCM3 (A1B), respectively. The results also indicated that these models and scenarios performance for simulation of temperature and rainfall are varied and thus a GCM need to be calibrated for different regions.The objective of this study was to evaluate the ability of ten GCMs and three Emission Scenarios to reproduce the rainfall and temperature parameters in Kermanshah, Ravansar and West Islamabad stations located inside Qaresou basin in Iran using the average weighting method, over 1989-2008 period. At first, the models output and the scenarios were provided for this period. Then, the models validation was carried out using Mean Absolute Error (MAE), Root Mean Square Error (RMSE), Model Bias, and Nash – Sutcliffe criteria. Moreover, the models and scenarios uncertainty analysis was assessed by the weighting method. Based on these criteria, HADGEM1 and BCM2 had the best efficiency in Kermanshah station for mean temperature and rainfall simulation respectively. For Ravansar station the best models were ECHO-G and HADCM3, while for West Islamabad was ECHO-G. The overall results of this analysis showed that the best applied GCMs and emission scenarios for simulation of temperature and rainfall in the study area are ECHO-G (A2) and HADCM3 (A1B), respectively. The results also indicated that these models and scenarios performance for simulation of temperature and rainfall are varied and thus a GCM need to be calibrated for different regions.https://ije.ut.ac.ir/article_54223_4bbffffd513696b13a751c3f12ceb47f.pdfFaculty of New Sciences and Technologies, University of TehranIranian journal of Ecohydrology2423-60981320141222Evaluation of the Efficiency of AWBM, Sacramento and Tank Rainfall Runoff Model in Runoff Simulation in Arazkoose - Goorganrood Basin, Golestan porovinceEvaluation of the Efficiency of AWBM, Sacramento and Tank Rainfall Runoff Model in Runoff Simulation in Arazkoose - Goorganrood Basin, Golestan porovince2072215422510.22059/ije.2014.54225FAHosseinSalmaniPhD Student, Gorgan University of agricultural sciences and natural resources, GorganAbdolrezaBahremandGorgan University of agricultural sciences and natural resources, GorganKazemSaber ChenariPhD Student, Gorgan University of agricultural sciences and natural resources, GorganMohammadRostami KhalajPhD Student, Faculty of Natural Resources, University of Tehran, KarajJournal Article20150106According to variety of accessible hydrological models, evaluateing the efficiency of models for different management objectives are essential. Therefore, models with simple structure and using minimal input that can provide an acceptable result can serve as an effective tool to watershed managers. Hence, the objective of this research is to evaluate the relative performances of the lumped conceptual-based hydrological AWBM, Sacramento and Tank rainfall runoff models for daily simulation in Arazkoose tributary of Goorganrood River, Golestan porovince. Automatic calibration of the models were done for a 5-year period (1984-1988), followed by a 4-year validation period (1992-1995). The results were evaluated by several criteria, i.e. Root Mean Square Error (RMSE) and Nash coefficient efficiency coefficient (ENS) and the coefficient of determination (R2). According to the evaluation criteria the results were satisfactiory. Statistic and graphic results show that Sacramento model is performing most accurately among the models with R2= 0.823, ENS= 0.677 and RMSE= 4.565 in calibration periods and R2= 0.719, ENS= 0.669 and RMSE= 7.905 in validation periods. Simulation of the Models was more accurate for calibration period rather than validation period. Also the models’ minimum and average values of runoff are accurate and despite good simulated peak flow values, the results show that the models cannot accurately simulate all of the peak values. Since these models do not require much input data and their use is not time-consuming and costly, they can be preferred for surface water resources management.According to variety of accessible hydrological models, evaluateing the efficiency of models for different management objectives are essential. Therefore, models with simple structure and using minimal input that can provide an acceptable result can serve as an effective tool to watershed managers. Hence, the objective of this research is to evaluate the relative performances of the lumped conceptual-based hydrological AWBM, Sacramento and Tank rainfall runoff models for daily simulation in Arazkoose tributary of Goorganrood River, Golestan porovince. Automatic calibration of the models were done for a 5-year period (1984-1988), followed by a 4-year validation period (1992-1995). The results were evaluated by several criteria, i.e. Root Mean Square Error (RMSE) and Nash coefficient efficiency coefficient (ENS) and the coefficient of determination (R2). According to the evaluation criteria the results were satisfactiory. Statistic and graphic results show that Sacramento model is performing most accurately among the models with R2= 0.823, ENS= 0.677 and RMSE= 4.565 in calibration periods and R2= 0.719, ENS= 0.669 and RMSE= 7.905 in validation periods. Simulation of the Models was more accurate for calibration period rather than validation period. Also the models’ minimum and average values of runoff are accurate and despite good simulated peak flow values, the results show that the models cannot accurately simulate all of the peak values. Since these models do not require much input data and their use is not time-consuming and costly, they can be preferred for surface water resources management.https://ije.ut.ac.ir/article_54225_fd2da0bd0900bf176d6cc142fd77b864.pdfFaculty of New Sciences and Technologies, University of TehranIranian journal of Ecohydrology2423-60981320141222Investigation of Zeolite and Perlite equilibrium isotherms in Sodium Chloride adsorption of the salt watersInvestigation of Zeolite and Perlite equilibrium isotherms in Sodium Chloride adsorption of the salt waters2232325422710.22059/ije.2014.54227FAFatemehShokrianPh.D. student of watershed management, Sari University of Agricultural and Natural ResourcesKarimSolaimaniSari University of Agricultural and Natural Resources0000000253576797Ghorban AliNematzadehSari University of Genetic and Agricultural Biotechnology Research Institute (GABIT)PouryaBiparvaBasic sciences group, Sari University of Agricultural and Natural ResourcesJournal Article20150204Deficiency of water resources is one of the major challenges at the global scale and also in Iran. The existence water resources of oceans and seas such as the Caspian Sea and Persian Gulf in the north and southern parts of Iran respectively, can be considered as the alternative to dominate the future problem. This study is processed absorption of Nacl based-on natural Zeolite and Perlite. In order to obtained of different sizes in five classes, the standard sieves used based on ASTM with determined D of 20, 40, 80, 120 and 200 for granulometric process. The salty water used with different concentration in the range of 25 to 10000 mg/l. To determine the rate of chloramine in samples nitrate of silver with 0.02 mol and potassium chromate used as indicator for detecting of chloramine titration in suspension. The effects of different parameters were examined such as concentration, adsorbent dosage and particles size. The extracted results had indicated that, with declination of the particles size, it can be expected to increase the percentage of sodium chloride removal. Similarly, due to increasing the adsorbent dosage, more absorption will increase in this process. The Freundlich and Langmuir models were used to obtain the isotherm equilibrium curve. The results showed that sodium chloride absorption had a better fitting (R2 97%) using Zeolite from Freundlich model and Perlite also with a meaningful of (R2 96%) in Langmouier model.<br />Keywords: Equilibrium isotherm, Mineral adsorbents, Freundlich, Langmouir and CaspianDeficiency of water resources is one of the major challenges at the global scale and also in Iran. The existence water resources of oceans and seas such as the Caspian Sea and Persian Gulf in the north and southern parts of Iran respectively, can be considered as the alternative to dominate the future problem. This study is processed absorption of Nacl based-on natural Zeolite and Perlite. In order to obtained of different sizes in five classes, the standard sieves used based on ASTM with determined D of 20, 40, 80, 120 and 200 for granulometric process. The salty water used with different concentration in the range of 25 to 10000 mg/l. To determine the rate of chloramine in samples nitrate of silver with 0.02 mol and potassium chromate used as indicator for detecting of chloramine titration in suspension. The effects of different parameters were examined such as concentration, adsorbent dosage and particles size. The extracted results had indicated that, with declination of the particles size, it can be expected to increase the percentage of sodium chloride removal. Similarly, due to increasing the adsorbent dosage, more absorption will increase in this process. The Freundlich and Langmuir models were used to obtain the isotherm equilibrium curve. The results showed that sodium chloride absorption had a better fitting (R2 97%) using Zeolite from Freundlich model and Perlite also with a meaningful of (R2 96%) in Langmouier model.<br />Keywords: Equilibrium isotherm, Mineral adsorbents, Freundlich, Langmouir and Caspianhttps://ije.ut.ac.ir/article_54227_82533ec6ae1fa1a534a0415ccedb3b7c.pdfFaculty of New Sciences and Technologies, University of TehranIranian journal of Ecohydrology2423-60981320141222Monitoring of Khiav River Water During Exploration Well Drilling at Sabalan Geothermal Field, Northwestern IranMonitoring of Khiav River Water During Exploration Well Drilling at Sabalan Geothermal Field, Northwestern Iran2332415422810.22059/ije.2014.54228FAYounesNoorollahiFaculty of New Sciences and Technologies, University of Tehranhttps://orcid.org/00HosseinYousefiFaculty of New Sciences and Technologies, University of Tehran0000-0002-6372-5127SaeidehSadeghiFaculty of New Sciences and Technologies, University of TehranSaeidMohamadzadeh BinaDep. of Energy, Graduate School of Environmental and Energy, Islamic Azad University, Sciences and Research BranchSaraSadeghiFaculty of Marine Sciences and Technologies, Islamic Azad University, Tehran North BranchJournal Article20150119In this paper, the results of surface and ground water quality monitoring during drilling of three deep exploratory wells in geothermal project in North West of Sabalan in Meshkinshahr are analyzed. The region has been investigated by various researchers to generate electricity using geothermal energy. Drilling in deep geothermal projects, a variety of materials such as cement, bentonite, barite, soda ash, sodium chloride, etc. are used in the process of drilling and fixing wells enabling large amounts of pollutants into the aquifers that may discharge into the Khiav River. This study have tried to identify the possible effects of drilling three exploration wells on the Khiav River and hot and cold springs in an area in Sabalan. The water quality of Khiav River is very important because it supplies drinking and irrigating water for Meshkinshahr city and suburbs with a population about 200, 000 people. Residents of villages and many nomadic families use cold springs as drinking water sources in the summer, as well as many tourists who travel there to visit touristic attractions and hot springs may be affected by possible changes in water quality of these springs. Therefor monitoring the changes in the quality of hot and cold springs in the area is significantly important. The results of an 18 months of investigation indicate that drilling activities have no significant effect on the water quality of Khiav River and springs. Levels of some high heavy metals concentrations of other elements are less than the standard for drinking water.In this paper, the results of surface and ground water quality monitoring during drilling of three deep exploratory wells in geothermal project in North West of Sabalan in Meshkinshahr are analyzed. The region has been investigated by various researchers to generate electricity using geothermal energy. Drilling in deep geothermal projects, a variety of materials such as cement, bentonite, barite, soda ash, sodium chloride, etc. are used in the process of drilling and fixing wells enabling large amounts of pollutants into the aquifers that may discharge into the Khiav River. This study have tried to identify the possible effects of drilling three exploration wells on the Khiav River and hot and cold springs in an area in Sabalan. The water quality of Khiav River is very important because it supplies drinking and irrigating water for Meshkinshahr city and suburbs with a population about 200, 000 people. Residents of villages and many nomadic families use cold springs as drinking water sources in the summer, as well as many tourists who travel there to visit touristic attractions and hot springs may be affected by possible changes in water quality of these springs. Therefor monitoring the changes in the quality of hot and cold springs in the area is significantly important. The results of an 18 months of investigation indicate that drilling activities have no significant effect on the water quality of Khiav River and springs. Levels of some high heavy metals concentrations of other elements are less than the standard for drinking water.https://ije.ut.ac.ir/article_54228_598351593ee10891a189db816b3a249a.pdfFaculty of New Sciences and Technologies, University of TehranIranian journal of Ecohydrology2423-60981320141222English AbstractsEnglish Abstracts175439010.22059/ije.2014.54390FAJournal Article20150802https://ije.ut.ac.ir/article_54390_7dc21871d899d11428d60514649e9b10.pdf